1 / 11
Häner HCM500R for wheel loaders without mount
- Current bid
- Status
€
Total bid amount
See total breakdown
Total bid amount
See total breakdown
€
Max bid amount
See total breakdown
Max bid amount
See total breakdown
Lot specifications
- Quantity
- 1
- Margin
- No
- Brand
- Häner
- Year of build
- 2025
- Own weight
- 770kg
Description
HÄNER HCM500 Concrete Mixing Bucket for Wheel Loader
New device
Working width: 1800 mm
Height: 900 mm
Depth: 930 mm
Nominal capacity: 500 l
Maximum capacity: 550 l
Curb weight: 770 kg
Concrete weight: 1200 kg
Total weight: 1970 kg
Required oil volume: 60-150 l/min
Maximum pressure range: 240 bar
Drive Type Mixing Shaft: Chain
Important safety note: The total weight of the mixing bucket may not exceed 90% of the tipping load (kinked) of the carrier device.
Our HCM500 concrete mixing bucket has the following data and specifications:
– Side panels made of 12 mm S355
- Base body made of 10 mm S355
– Mixer screw rings made of wear-resistant HB500; Thickness 15 mm
– Mixer shaft made of C45 solid steel; Diameter 65 mm
- Cutting edge made of 20mm HB400
– Roller bearings with free-moving rollers
– central hydraulic drain port piston rod protection
– high-quality hydraulic motor (similar to EATON)
– Solenoid valve for drain opening (optional)
– galvanized mesh opening with teeth to tear
open bags – 12V electrical kit (optional)
– Changing system for screw adapters
– Rubber drain hose with guide rod
– CE certificate with operating and maintenance instructions
New device
Working width: 1800 mm
Height: 900 mm
Depth: 930 mm
Nominal capacity: 500 l
Maximum capacity: 550 l
Curb weight: 770 kg
Concrete weight: 1200 kg
Total weight: 1970 kg
Required oil volume: 60-150 l/min
Maximum pressure range: 240 bar
Drive Type Mixing Shaft: Chain
Important safety note: The total weight of the mixing bucket may not exceed 90% of the tipping load (kinked) of the carrier device.
Our HCM500 concrete mixing bucket has the following data and specifications:
– Side panels made of 12 mm S355
- Base body made of 10 mm S355
– Mixer screw rings made of wear-resistant HB500; Thickness 15 mm
– Mixer shaft made of C45 solid steel; Diameter 65 mm
- Cutting edge made of 20mm HB400
– Roller bearings with free-moving rollers
– central hydraulic drain port piston rod protection
– high-quality hydraulic motor (similar to EATON)
– Solenoid valve for drain opening (optional)
– galvanized mesh opening with teeth to tear
open bags – 12V electrical kit (optional)
– Changing system for screw adapters
– Rubber drain hose with guide rod
– CE certificate with operating and maintenance instructions
Additional details
LOADING: The loading of the auctioned goods is only possible in suitable vehicles or trailers; Cars cannot be loaded. Heavy and large equipment must not be loaded into vans, as axle loads and load securing must be observed. All equipment is provided on suitable pallets and can be loaded by forklift, provided that a suitable transport vehicle is available.
LOADING ASSISTANCE: 3000 kg forklift and 5000 kg crane available.
VAT DEPOSIT: Business buyers from the European Union (EU) and non-EU countries (third countries) are obliged to pay a deposit to Troostwijk Germany on their total purchase. This deposit is calculated on the basis of the VAT rate applicable in the Federal Republic of Germany. After confirmation that the purchased lot has left the EU, the deposit will be returned to the buyer:
• EU buyers must complete a completed confirmation of success [download the template "Template_Intra-Community Supply (DE-EN)" attached here] to Troostwijk Germany and return the deposit to export.de@troostwijkauctions.com in order to receive a refund.
• Non-EU buyers must return a copy of the electronic export declaration (EX-A with MRN - for verification only) or, if the value of the goods is lower, a completed export declaration with a stamp from the EU border customs office to export.de@troostwijkauctions.com in order to get the deposit refunded.
