1 / 25
Häner HCM250R+B for excavators and wheel loaders without mount
- Current bid
- Status
€
Total bid amount
See total breakdown
Total bid amount
See total breakdown
€
Max bid amount
See total breakdown
Max bid amount
See total breakdown
Lot specifications
- Quantity
- 1
- Margin
- No
- Brand
- Häner
- Year of build
- 2025
- Own weight
- 505kg
Description
HÄNER HCM250 Concrete mixing bucket for wheel loaders and excavators without mount
Working width: 1140 mm
Height: 890 mm
Depth: 710 mm
Nominal capacity: 250 l
Maximum capacity: 290 l
Curb weight: 505 kg
Concrete weight: 605 kg
Total weight: 1080 kg
Required oil volume: 40-90 l/min
Maximum pressure range: 240 bar
Drive Type Mixing Shaft: Chain
Important safety note: The total weight of the mixing bucket may not exceed 90% of the tipping load (kinked) of the carrier device.
Our HCM250 concrete mixing bucket has the following data and specifications:
– Side panels and base body made of 10mm S355
– Mixer screw rings made of wear-resistant HB500; Thickness 12 mm
– Mixer shaft made of C45 solid steel; Diameter 65 mm
- Cutting edge made of 20mm HB400
– Roller bearings with free-moving rollers
– central hydraulic drain port piston rod protection
– high-quality hydraulic motor
– Solenoid valve with 12V electrical kit for drain opening
– galvanized mesh opening with teeth to tear
open bags – Interchangeable system for excavators and wheel loaders
– Rubber drain hose with guide rod
– CE certificate with operating and maintenance instructions
Working width: 1140 mm
Height: 890 mm
Depth: 710 mm
Nominal capacity: 250 l
Maximum capacity: 290 l
Curb weight: 505 kg
Concrete weight: 605 kg
Total weight: 1080 kg
Required oil volume: 40-90 l/min
Maximum pressure range: 240 bar
Drive Type Mixing Shaft: Chain
Important safety note: The total weight of the mixing bucket may not exceed 90% of the tipping load (kinked) of the carrier device.
Our HCM250 concrete mixing bucket has the following data and specifications:
– Side panels and base body made of 10mm S355
– Mixer screw rings made of wear-resistant HB500; Thickness 12 mm
– Mixer shaft made of C45 solid steel; Diameter 65 mm
- Cutting edge made of 20mm HB400
– Roller bearings with free-moving rollers
– central hydraulic drain port piston rod protection
– high-quality hydraulic motor
– Solenoid valve with 12V electrical kit for drain opening
– galvanized mesh opening with teeth to tear
open bags – Interchangeable system for excavators and wheel loaders
– Rubber drain hose with guide rod
– CE certificate with operating and maintenance instructions
Additional details
LOADING: The loading of the auctioned goods is only possible in suitable vehicles or trailers; Cars cannot be loaded. Heavy and large equipment must not be loaded into vans, as axle loads and load securing must be observed. All equipment is provided on suitable pallets and can be loaded by forklift, provided that a suitable transport vehicle is available.
LOADING ASSISTANCE: 3000 kg forklift and 5000 kg crane available.
VAT DEPOSIT: Business buyers from the European Union (EU) and non-EU countries (third countries) are obliged to pay a deposit to Troostwijk Germany on their total purchase. This deposit is calculated on the basis of the VAT rate applicable in the Federal Republic of Germany. After confirmation that the purchased lot has left the EU, the deposit will be returned to the buyer:
• EU buyers must complete a completed confirmation of success [download the template "Template_Intra-Community Supply (DE-EN)" attached here] to Troostwijk Germany and return the deposit to export.de@troostwijkauctions.com in order to receive a refund.
• Non-EU buyers must return a copy of the electronic export declaration (EX-A with MRN - for verification only) or, if the value of the goods is lower, a completed export declaration with a stamp from the EU border customs office to export.de@troostwijkauctions.com in order to get the deposit refunded.
